More Details

What're your ideas concerning How to Install a Bathtub?

Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old tub with a new one is also a reasonably difficult task. If the old bathtub is readily accessible, the task can move easily; if you need to open up a wall surface to eliminate the old bathtub and also place the brand-new bathtub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old tub and set in the brand-new one. Make sure you have certified yourself for the task and also fit attempting it. As opposed to employing a contractor to take over a halfway-completed job, it is far better to take into consideration utilizing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will certainly help you mount a brand-new tub in your shower room if you have actually already gotten a brand-new bathtub as well as do not need to transform the setup of your previous supply of water pipes.
Your devices as well as product checklist ought to consist of the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Getting ready for the Installation

Firstly, the sustaining frame provided with the bathroom needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its final placement.

Removing Old Taps

If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is detach the water supply. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing faucets can be fairly troublesome due to the limited accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the staying water that will originate from the pipes. When the supply pipes have actually been eliminated, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.

Setting up the Bath tub

Using both wood boards under its feet, place the bath tub in the required setting. The wooden boards are useful in equally spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and changing the feet on the bathtub up until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the various other tap.
Switch on the water and check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Lastly, take care of the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait till the tub has actually been made use of a minimum of once as this will resolve it right into its last placement.

Suitable New Taps

If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washers are in area between the tap as well as the sink. Protect the tap in place with the producer provided backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The former kind ought to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

Tiling Around the Bath tub

In the area where the bathroom satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, leading to complications with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components and installations. They are sold in tubes and also cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can split fairly early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently offered on the market. It is a good idea to fit the ceramic tiles using water-resistant or water resistant glue as well as cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you appreciate reading about Tools You Need to Install a New Bathtub ? Leave a remark directly below. We'd be glad to know your opinions about this blog. We hope that you visit us again in the near future. Are you aware of someone else who is truly interested in How to Install a Bathtub? Why not share it. Thank you for going through it.

Maintain plumbing health; connect today.